AER has reduced the frequencies for several types of Calibrations. Here is a link to a pdf “Calibration Frequency Cheat Sheet” Many found helpful.

We have setup one of our test separators to work well for cardium well testing.

1440PSI 20″x 8′ 3 phase but dressed 2 phase 

with Peterson Sampler on emulsion.  

Chart Recorder, 2″ Northstar Jr. OrificeChanger

on 16′ Tandem Car Hauler Trailer.

When we do a EFM  Calibration or verification, our trained staff follow all manufacturer’s recommended procedures. We the calibration and verification requirements in AER Directive 017 are followed.

We also verify not only the EFM itself, but check the orifice run and inspect the orifice plate and changer if possible. We have found damaged orifice seals, and nicked plates which affect accuracy. For example we found a large error caused by an orifice plate with the wrong size stamped on it which was in service for several years. This was found by routinely checking orifice plate sizes with calipers.

At Measurement Inc.  we encourage a safe and healthy work environment, and we are working diligently to ensure the good health of every employee and customer that is in need of our continued services.  We continue to offer the Essential Services required to continue operations of oil gas facilities, in the areas of Instrumentation, Measurement and Proving.

As well, to comply with COVID-19 social distancing recommendations and ensure everyone’s safety, our technicians are offering NO CONTACT SERVICES that allow you to complete a booking and service appointment with no physical interaction or contact.

Our COVID-19 Safety Protocol for Essential Work

• Measurement Inc will follow all Alberta Health Requirements regarding COVID-19.  Identifying and isolating people with COVID-19 is the only way to stop the spread.  The symptoms of COVID-19 are fever, dry cough, difficulty breathing or other cold and influenza-like symptoms.  Online screening/self-assessment is available: Alberta Self-Assessment (Health Link 811).

Anyone who enters Canada from abroad must immediately self-isolate for 14 days upon return. Anyone who has symptoms must self-isolate for 14 days.  Please do not visit a hospital, physician’s office, lab or healthcare facility without consulting Health Link first.

• Complete the necessary Safe Work Permit, addressing specific COVID-19 precautions.
• The supervisor will ask if any workers have COVID-19 like symptoms, and if they do, work should not proceed.  Workers who are ill or who present any COVID-19 symptoms including fever cough or difficulty breathing are not permitted to travel to work sites.
• All workers must follow proper handwashing (warm soap and water for 20 seconds) or use hand sanitizers when soap and water isn’t available.
• Practice social distancing (~2m distance between workers) including when work is being done and when on breaks.  
• Conduct pre-job  safety meetings outside  if possible, maintain social  distancing of about 2m between workers.  Workers do not have to sign on to safe  work permit (print names of all workers). Do not share  pens or paperwork.
• Cough into arm, use tissues and properly dispose of waste.

 Ordering a NO CONTACT SERVICE

1.       Book your service right away online or by phone call: 780-621-2555 or email jerry@measurementengineering.com .

2.       Prior to the appointment, your technician will call and confirm the specifications of the service you require.

3.       Once onsite, a Safe Work Permit/ Hazard Assessment will be completed, and a picture emailed/ texted to each party. These will not be signed, but will list the names of all involved so as not to share pens and paper.

4.       Your technician will complete the service and notify you that the service has been completed, with pictures, for your reference.

5.       We will then send you an invoice and reports via email for payment.

It is a privilege to be of service to our local communities during this unprecedented time. We appreciate your support as we are a local business doing everything we can to support our customers, our families and our communities.

If you have any questions please contact us.

Thank you for your continued and valued support!

Jerry Greiner,

Measurement Inc.

Phone 780-621-2555, 

Email jerry@measurementengineering.com

We provide value to our customers through a few different ways.

 All of our data is entered directly into a database, where it is searchable and easily stored as a pdf. Paper copies are printed off and left onsite.

This database helps in scheduling and keeping track of past and upcoming calibrations.  When a problem is found we can quickly search to see if this would affect any other sites we have been at as well.

The operator and scheduler’s job is easier knowing that there is a double check of missed meters each time, making the audits much easier.

Clients have commented how the measurement audits go so smoothly for the areas we look after compared to other areas. 

You can measure our success with your next measurement audit.  See how the areas we look after compare to other areas in the company.  

We bring this value to You with our services.

Should you have any questions regarding any information please feel free to contact us using the following information below.

Jerry Greiner(President)

jerry@measurementengineering.com

Telephone :             (780) 514-5010      

Fax : (Edmonton Direct)             (780)665-6162      

 P.O. Box 7867

5428B Industrial Road.

Drayton Valley, AB

T7A 1S9

Thank-You for visiting us and we hope to hear from you soon.